CDA PC44 Instruções de Operação Página 46
- Página / 104
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
3-24 Installation
9. PC40 Remote
Communications Installation
The following information is provided
if
you will be using a remote
device
to
se
lect active memory and/or lock out input through the PC40
user interface.
Remote connections are made to
PC40 terminal block
P1
(Figure 3.9).
Signals connected to
P1
are optically isolated from the remote system.
The opto-isolators can be turned
on
by either current sourcing
or
current sinking devices.
Remote Pin Characterization
Table
3
~
9
- Remote Communication Pin Characterization
Pin
P1-1
("Shield")
P1-2 ("Ground")
P1
-3 ("Common")
Pl-4
("lock")
P1-5 ("Remote
Memory Select 3")
P1
-6 ("Remote
Memory Select 2")
P1-7 ("Remote
Memory Select 1 ")
P1-8
{"+1
2V")
PIN
10838
9A
57
-28
11!13
Function
Provided for field wiring convenience.·
Provided for field wiring convenience.
Provides
for
one half
of
the connection for
all of the opto
-i
solators.
Provides
for
a remote signal to disallow
access
to
the PC40 Program Mode.
Provides con
ne
ction to allow a remote
devi
ce
to
change the active memory.
Provides connection to allow a remote
device to change the active memory.
Provides connection to allow a remote
device to change the active memory.
Provides 12 VDC input power for any
remote
dev
ice that requires it.
Comments
Connected
to
the remote device
1/0
printed circuit board.
Connected
to
the remote device
1/0
printed circuit board.
For sourcing
(PNP) devices, P1-3 should
be connected to
P1-2 ("Ground"). For
sinking
(NPN) devices, P1-3 should be
connected
to
P1-8 ("+12V").
Maximum current available from pin
P1
-8
is 500 mA.This is the maximum current
available for
all connections to pin
P1
-8
including loads on other PC40 connectors.
C N
ord
son Corporation 1993
All
R
1g
~
ts
Reserved
- PC40 240 VAC 1
- Pattern 1
- Control 1
- 1994 Nord 2
- Table of Contents 3
- Sectlon4 4
- Operating Instructions 4
- Contents 5
- Safety Summary 7
- Section 1 9
- Safety During Installation 10
- Equipment Familiarization 11
- Section 2 13
- Equipment 13
- Familiarization 13
- Jrr=r-· 15
- (Figure 2.4) 17
- Nordson Photoelectric 18
- Sensors 18
- Retroreflectlve 19
- Remote Communications 20
- Installation 21
- Section 3 23
- 3-2 Installation 24
- Mounting the PC40 24
- Enclosure 24
- Machine Mounting 25
- DIN Rail Mounting 25
- Installation 3-3 25
- 3-4 Installation 26
- 2 - Back enclosure 27
- '8 28
- PC40 Electrical Connections 29
- 3-8 Installation 30
- Installation 3-9 31
- 0 Installation 32
- 1'9 33
- Solenoid Wiring Installation 34
- ! PC40 installation 35
- 3-14 /nstalfation 36
- "" 37
- (continued) 38
- Mounting Dimensions 39
- Mounting Nordson Sensors 39
- Installation 3-17 39
- 3-18 Installation 40
- Installation 3-19 41
- 3-20 Installation 42
- Nordson Photosensor Wiring 43
- Connections 43
- .....,.....>-! 44
- Aligning 45
- Installation 3-23 45
- 9. PC40 Remote 46
- Communications Installation 46
- - Remote Memory Select Logic 47
- 0 Natdson Corporabon 1993 49
- AI Rights Resetved 49
- 3-28 Installation 50
- Installation 3-29 51
- ~---------+4------8 52
- 3-32 Installation 54
- Section 4 57
- 2 3 4 58
- Trigger 59
- C) Nord son 60
- ..----4 61
- .._--4 62
- 1 63
- --------· 63
- Setting Up the Pattern 64
- Operating Instructions 4-9 65
- ~is~nce 66
- ...,._--5 67
- 4-12 Operating Instructions 68
- ~~·---------------788 69
- 1 _ I _ I _ I 70
- I I I I I 71
- ·x· flashing 72
- Programming 73
- Raserve<l 74
- Programming Channel 75
- Nordson Corporalion 1 76
- • The right-most digit 77
- Transition 78
- 2. Press DOWN 79
- (rUSHING) 80
- PROGRAH 81
- 6. Run Mode 83
- 4-28 Operating Instructions 84
- 8 C D X+:-:----1 85
- ·o•, is flashing 86
- Operating Instructions 4-31 87
- Troubleshooting 89
- Section 5 91
- 4. Guns Not Firing 92
- Firing {continued) 93
- 5. Gun(s) Firing Between 94
- Patterns 94
- Gun(s) Firing Between 95
- Other Gun Firing Problems 95
- 5-6 Troubleshooting 96
- Reference Data 97
- Section 6 99
- Service Parts 100
- Number Part Number 101
- Description 101
- Req'd 101
- 6-4 SeNice Parts 102
- Specifications 103
- Reference Data 6-5 103
- 6-6 Service Parts 104
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais